nobcha23のエアバンド受信機自作ブログ DIY airband receiver BLOG

エアバンドレシーバーキットの組み立て、改造を手掛けます Assemble and remodel Chinese airband receiver kit

2021-01-01から1年間の記事一覧

There is an article on "Silicon Chip" magazine Nov 2021 issue. シリコンチップと言うWEB雑誌にR80記事あり

window.dataLayer = window.dataLayer || []; function gtag(){dataLayer.push(arguments);} gtag('js', new Date()); gtag('config', 'UA-82470304-2'); Silicon Chip(au)と言うマガジンにR80の記事が載っています。R80_V6とR80_V7の説明書(英語)がア…

R80 V6エアバンドレシーバーキットの説明書(日本語版)を作製してみました

R80 118-136MHz Air Band Receiver Aviation Radio Receiver PLL Double Frequency Conversion Assembled - Free Shipping - ThanksBuyer 5351aを局発に使い、安定待ち受け受信できる新しいキットR80(Ver6)の日本語版説明書を作製してみました。http://chito…

R80 V7って? What is R80 v7 radio?

window.dataLayer = window.dataLayer || []; function gtag(){dataLayer.push(arguments);} gtag('js', new Date()); gtag('config', 'UA-82470304-2'); ユーチューブを流し見していたら、R80の基板リビジョンPCB HM00ABRC_7でFMも聞けるようになったとの紹…

Assembling R80 kit PART4- Assembled with several improvement  R80キットの組立 その4 組み立てました

Finally, I had finished assembling the kit. There is remaining much noise in spite of receiving the signal. So I had been worried that there were some issues. The squelch is unstable and the squelch will close when the strong signal is com…

Assembling R80 kit PART3- FIL/LNA check  R80キットの組立 その3 フィルターとLNAの通過特性

After assembled, I had adjusted and could receive the signal. However, it is very much noisy. I'm afraid of remaining some issues. BTW I checked the passband characteristics for the front filter and LNA by using nano VNA. As LNA is 20dB ga…

Assembling R80 kit PART2- Voltage check list  R80キットの組立 その2 各部電圧チェック用目安リスト

I completed assembling the kit. Some noisy sound comes out from the speaker. I resumed the voltage list of each IC node. The voltage is measured by a digital tester at DC mode.This is for simple checking to avoid mistaken wiring or parts s…

Assembling R80 kit PART1- Parts list  R80キットの組立 その1 パーツリスト

I just received the kit from China and would like to start assembling it. However, there was no document with it. So I shall prepare the list by myself. Prior to soldering, I put the parts in order to check the contents being enough.I adhe…

Studying R80 circuit diagram PART5 Squelch and audio circuit  R80回路図の研究 その5 スケルチ、音声増幅回路

After FM62429 variable attenuator the audio signal is going to LM386 amp.The same signal is going to the MC3661 filter amp and detector. MC3361 is naturally the FM receiver IC and this receiver is using filter amp for detected signal AMP t…

Studying R80 circuit diagram PART4 -IF, Mixer & DET  R80回路図の研究 その4 第一、第二中間周波数AMP、ミキサー、検波

c. 1st IF AMP, 2nd mixer, 2nd IF AMP, and detecter MC3661 is working as the 1st IF AMP and also the 2nd mixer combined with 10.245MHz crystal oscillator. The output of MC3661 is fed into LT455 ceramic filter prior to TA7640.TA7640 is worki…

Studying R80 circuit diagram PART3 -Mixer &LO  R80回路図の研究 その3 ミキサーと局部発振器

The 1st local oscillator is MS5351 PLL managed by PIC18F1320. There is a rotary encoder to tune the frequency. We can select 100kHz or 10kHz step frequency by pushing the RE knob. The frequency is displayed on the front 7 segments 4 column…

「Studying R80 circuit diagram 」 PART2,「回路図の研究」その2 #FIL&LNA回路図

The circuit of R80 front end section a. The front end filter and LNA The front stage filter is a stager style with two LC resonating circuits.L is D5x5 size, 4.5 turn(Estimated inductance is 68nH by WEB service "http://gate.ruru.ne.jp/rfd…

I'm studying R80 receiver kit PART1  中国製エアバンド受信機キットのR80を調べてみました(その1)

The block diagram of R80 receiver I'm wondering to buy R80 kit or not. I have been interested in various functions on R80. 1. They are saying that the LO is PLL. And I had come to know that the chip was MS5351 as was Si5351a clone.If so, t…

中国製PLL式局発のエアバンド受信機R80のPLL局発は5351らしい   PLL LO chip may be the 5351a clone

少し前のブログ(と言ってももう一年近く前)でPLL方式局発のエアバンド受信機キットがあることを紹介しました。 nobcha23.hatenadiary.com 買って試そうかなと迷ってましたが、最近konさんと言う方のWEBで詳しく紹介されているのがわかりました。キット入手…

Si4732基板を買いました  その4  I bought Si4732 kit. part 4  Filter→LNA→Mixer@crystal converter

window.dataLayer = window.dataLayer || []; function gtag(){dataLayer.push(arguments);} gtag('js', new Date()); gtag('config', 'UA-82470304-2'); Si4732受信機基板セットを買ったので、これでエアバンド通信を聞こうと考え、周波数コンバーターを作…

オリジナルケースにデジタル局発も入れる (その2)  To install the digital LO into the Chinese original aluminum case with receiver kit. (2nd)

二号機組立状況 The report of 2nd machine assembled 中国製エアバンド受信機キット用オリジナルアルミケースにデジタル局発も一緒に入れるという改造を行いました。 I had installed the optional digital LO circuit into the Chinese original case with…

Si4732基板を中国製エアバンドレシーバーキットにつないでみた  Connect Si4732 kit with Chinese airband receiver kit  (Si4732基板を買いました その3 I bought Si4732 kit. part 3)

Si4732を使用したpu2clrライブラリー対応受信機を買って動かしました。これはケース入りでATS-20という名称にて売られているらしいものです。それに使われているらしい基板をキットで買いました。そして、どうもソースは基板だけトルコのTB5CVNというハムが…

Si4732基板が動かない->動いた!  Chinese Si4732 kit is out of order (Si4732基板を買いました その2 I bought Si4732 kit. part 2)

――中国製Si4732基板を組立、動かしました―― 次ステップにおけるデバッグのことを考慮し、nano基板実装はソケット接続に変更し、SSD1306LCD基板もコネクタ・ケーブル接続にします。中国からメイン基板に乗ってやってきたnano基板ですが、メイン基板に刺さって…

Si4732基板を買いました  その1  I bought Si4732 kit. part 1

Si4732とSi5351aの組み合わせで航空無線受信機を作ってみようと思っています。 今までのところ、中国製エアバンド受信機基板キットを組立て、改造し、デジタル化局発受信機ができました。なかなか使い勝手良いので、これをもとに中間周波数以下をSi4732へと…

How to improve squelch feeling for Chinese air band receiver kit 中国製エアバンドレシーバーキットのスケルチフィーリング改善

This article is re-edited from the former post. The pop sound is coming out when the squelch is on/off. AGC voltage and squelch volume tuning voltage are compared by LM358 and the circuit is muting RX sound signal at LM386 input neverthele…

オリジナルケースにデジタル局発も同居させる(その1) I would like to install digital local oscillator with into the original case(Part1 :New sketch)

中国製エアバンドレシーバーキット改造に取り組んでいます。外部デジタル局発もオリジナルアルミケースに一緒に入れられないかと考えました。 まずは表示ですが、SSD1306コントローラ搭載のグラフィック液晶をキャラクタ液晶替わりに使いました。 グラフィッ…

中国製エアバンド受信機キット+デジタル局発+SDRのアイデア There is an idea for combininng Chaina aiband receiver kit with SDR

PU2CLRのGITHUB情報をベースにした中国発クローン受信機(Si4732ーA10)が流行っていますね。 Chinese Si4732 receiver clone is coming to be popular. Also there was a project to combine Si4732 with Si5351a. エアバンドレシーバーキットの作成+追加…

キット改造改良点をまとめました  the issues to be improved

イタリアのロベルトさんからの指摘や、ワタシの方で気づいた改良点をまとめました。 I listed the issues improved for Chinese airband receiver kit performance as below. 1. To tune frontend filter coils コンデンサーを次段コイルパターン上へ倒す 2.…

エアバンドレシーバーキットの中間周波数信号10.7MHzをSi4735で聞いてみる

12.8MHzの発振器信号では味気ないので、実際の変調されている受信信号をSi4735で聞いてみようと、中華エアバンドレシーバーキットの10.7MHz中間周波数信号を取り出し、受けてみました。 中華エアバンドレシーバーキットSi4153a局発改造機のSA602→Xtalフ…

Si4735のSW受信実験:PU2CLRライブラリーを使用

Si4735モジュールを親受信機にしたエアバンド受信機を作れないかと実験をやってます。Arduino UNOとi2cでつなぎFM受信するのは簡単でしたが、SWはいまいち受かりませんでした。 まずはSi4735を使いこなせるようになりたいと実験進めています。 Si4…

キーパッド操作&i2cLCDのエアバンド受信機用局発(その2) LO operated by key pad with i2c LCD

キーパッドとPCF8574の組み合わせでキーパッドインターフェイスを作りました。 nobcha23.hatenablog.com このキーパッドとLCD&Keyシールドでエアバンド受信機用局発を作りました。 nobcha23.hatenadiary.com I had assembled key pad operated digital loca…

キーパッドで周波数指定するエアバンド受信機用局発(その1) Local oscillator operated by key pad

キーパッドとPCF8574の組み合わせでキーパッドインターフェイスを作りました。 このキーパッドインターフェイスを利用し、Si5351aを制御しエアバンド受信機用局発を作ることにします。必要な周波数カバーは118MHzから137MHzです。ただし、今回は実験用に30…

エアバンドレシーバーキット製作 第一ステップ(周波数表示)、第二ステップ(デジタル局発)

中華製エアバンドレシーバーキットを組立、改造、改良、回路追加しスキャン機能が付いた受信機セットを作りました。これをシャックにおいてエアバンドワッチに使っています。 キットを組立、ケースに入れて外部周波数カウンタにつないでワッチ周波数表示がで…