Mr.Prem Meno is introducing the newly R80 version of HM00ABRC_7 on the YOUTUBE video. New radio can receive FM also with airborne radio. Please refer to below the video in detail.
Mr. Prem gave me the comment as the squelch function is well, the sensitivity is less than his expected and good for receiving ATIS near the airport.
Depending on the schematic diagram, the LNA is omitted from V6, TA2003s are used as 1st mixer and AM/FM radio on 10.7MHz. Also, a noise amplifier is furnished by LMC6482.
Finally, I had finished assembling the kit. There is remaining much noise in spite of receiving the signal. So I had been worried that there were some issues.
The squelch is unstable and the squelch will close when the strong signal is coming. There is still sounding when the volume setting being 00. As the channel step is 10kHz, to listen xxx.475MHz we shall set xxx.480 or xxx.470 MHz.
To get soft sound, I added a high cut filter(1.6kΩ+0.1uF) on the audio line of LM386 input. It affected well to reduce noise. Changing ceramic filter to crystal filter is also reducing noise.
To stabilize squelch, I added 10uF on the SCAN signal line, but it does not affect so much.
Depending on nano VNA I adjusted the front end filter. Adding 1.5pF with at 15pF resulted in better sensitive
Green trace: CH0 impedance of smith chart
Orange trace: CH0 reflection
Blue trace: Passband characteristics
This receiver is useful for waiting for strong signals with a deep squelch.
Thanks, IMSAI GUY for your introduction on how to assemble and adjust by YOUTUBE.
After assembled, I had adjusted and could receive the signal. However, it is very much noisy. I'm afraid of remaining some issues.
BTW I checked the passband characteristics for the front filter and LNA by using nano VNA. As LNA is 20dB gain, I inserted 20dB ATT in the front of CH1.
Comparing with the former general gain estimation, there is a -6dB gain. The result is -11.72dB.
On the way to adjusting the front-end filter, the brass nuts are almost going out. We shall need the optional capacitors on paralleled 15pF.
This kit is more sensitive than the analog LO kit but SN ratio is much worse.
As there is no AGC, the signal strength feeling is not well. Also, SN ratio is low even for the strong signal.
Noise squelch circuits may be affected by static electricity. So the squelch circuit goes unstable. If you dare to use squelch, a deep setting is recommended. And you may utilize squelch only for fare strong signal only.
To get better performance for this kit, I should resolve the below issues.
1. To add the audio filter to avoid noize. 2. To stabilize the squelch circuit. 3. Audio volume issues that 2_00 is still signal being. 4. To add capacitors on the front-end circuit. 5. Is there well replacement for the squelch circuit. 6. To change 10kHz step to 25kHz step.
I'm much thanking kon for giving me the practical information of R80 kit.
I completed assembling the kit. Some noisy sound comes out from the speaker.
I resumed the voltage list of each IC node. The voltage is measured by a digital tester at DC mode. This is for simple checking to avoid mistaken wiring or parts swapping.
I also put a comment that it is noise sensitive node and the multi values for squelch ON/OFF or receiving/no signal.
I just received the kit from China and would like to start assembling it. However, there was no document with it. So I shall prepare the list by myself. Prior to soldering, I put the parts in order to check the contents being enough. I adhered the parts to the parts list to identify each other. Hurrying around is important for these complicated jobs.
I had inserted and soldered the part in turn along with the parts list order. Accordingly, the resisters were first, nextly the ceramic capacitors, the aluminum capacitors, and the others.
After soldering I found several residual parts of the capacitors.
When I used to connect DC supply for the first time, I should use the ampere meter to detect short circuits or some mistaken.
According to the SPEC, it consumes about 110mA. At this time I found the badly reversed installation of ATT-IC and no solder parts.
It is useful for the broadcasting channel to adjust the circuit. ITM ATIS of 128.6MHz is such a signal for me.
At this step, we shall adjust the sound volume, the squelch level, and the LO basic frequency compensation.
I referred to the manual in the below section.
------------------------------------------- Press the configuration button, after release, the configuration LED light will glow red, indicating that the encoder is in volume adjustment mode. The default display is 2_ 10 after power-on. The last two digits represent the volume level. The machine can be set to 0-25. The larger the number, the volume Bigger.
Press the button again, after release, display 3_ _XX, the last two digits represent the size of the squelch threshold, this machine can be set to 0-25, the larger the number, the higher the threshold (that is, the higher level of the received signal can exit the squelch state).
Press the knob again to display 4 _33, which is the 25MHz clock frequency offset setting. The default setting is 33 and the unit is 100Hz. The default frequency is 25 000 000Hz+33*100Hz. If you find an error in the receiving frequency, you can use a frequency meter to measure the 25MHz clock frequency on the PLL board and adjust the clock frequency deviation according to the test value.
FUNCTION MODE photo 25.000MHz FREQ 128.8MHz FREQ
As the frequency meter displayed 25.00192MHz, 4_19 should be an adjustment value. However, LO was 128.82MHz for receiving 128.1MHz. So I should adjust 4_52 for getting 128.8MHz LO. I don't know why such a difference.
As shallow squelch is hard to hear the signal, you shall set some deeper than 10.
I had compared R80 with 1st machine of remodeled Chinese kit(Degital LO).
After setting the parameters and adjustment for coils, nevertheless, the receiver could not demodulate a clear signal. The receiving LED was OK, and hiss noise had gone out. But I could not get a clear signal yet.
I shall need more investigation for the causes of undemanded demodulated sound.